This will ensure that the safety of the power tool is maintained. Slippery hands cannot safely control the power tool. Consult owners manual for proper part number identification and proper installation. NOTE: Do not wash the micro filter with soap and water. A vacuum hose adapter is included for connection of this tool to a 1-1/4" or 1-1/2" vacuum hose (Fig. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Compatible with: Bosch models: ROS10 (3601C87010) 5" Palm-Grip Random Orbit Sander, ROS20VS (3601C87511) 5" Variable Speed Palm-Grip Random Orbit Sander Kit, ROS20VSK (3601C87511) 5 in. Do not use sandpaper intended for larger sanding pads. This symbol designates that this tool is listed by Underwriters Laboratories. VARIABLE SPEED WITH DIAL SETTING (Model ROS20VS only). Power tools create sparks which may ignite the dust or fumes. Slippery hands cannot safely control the power tool. WARNING assembly, adjustments or changing accessories. Align new pad over locating pins on drive spindle, replace screws and securely tighten. Align locating bumps on damper ring with cut outs in shroud and depress ring with thumbs until shroud seats into groove completely around ring, then tighten screws (Fig. Crystalline silica from bricks and cement and other masonry products, and. Avoid accidental starting. Accidental start-ups may occur if sander is plugged in while changing an accessory. BM 2609140467 08-07 8/28/07 8:54 AM Page 8. Use smooth overlapping strokes for best results. Electrolux. Sanding particles can be absorbed by your eyes and inhaled easily and may cause health complications. Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up With the workpiece firmly secured, place the pad on the work surface, then switch the tool on. Power tools create sparks which may ignite the dust or fumes. The following table may be used as a general guide for abrasive and backing pad selection, but the best results will be obtained by sanding a test sample of the workpiece first. Larger sandpaper will extend beyond the sanding pad causing snagging, tearing of the paper or. Proper interpretation of these symbols will allow you to operate the tool better and safer. Manualer för kategorin Bosch Diskmaskiner. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. Diseñada con cuerpo y parte superior de agarre flexible y cómodo, esta lijadora de 2.5 A brinda 12,000 OPM para remoción de material de primera categoría. Keep the cord away from the spinning pad and sandpaper. Do not throw sanding dust on an open fire. Loose clothes, jewelry or long hair can be caught in moving parts. If you are experiencing premature wearout of the pad hooks, it may be due to pressure being applied to the tool during operation. Some applications, such as plastics, glass, or stone require silicon carbide discs, which have a very sharp cutting edge. Damaged or worn backing pads must be replaced immediately (Fig. Some dust created by power sanding, sawing, grinding, ... Read manual symbol Alerts user to read manual Wear eye protection symbol Alerts user to wear eye protection Use of the power tool for operations different from those intended could result in a hazardous situation. If your tool is equipped with a dust bag, empty it frequently and after completion of sanding. 2 Field / 120V. Never modify the plug in any way. If operating the power tool in damp locations is unavoidable a Ground Fault Circuit Interrupter (GFCI) must be used to supply the power to your tool. 4). Use of these devices can reduce dustrelated hazards. Download for 1. Maintain power tools. To remove dust canister: Twist the canister left or right and simply pull away from the tool (Fig. The random orbit sander is equipped with a backing pad of soft hardness, which is suitable for general service. The sander's orbital pad speed can be preset from zero to maximum nameplate OPM by rotating the dial in the housing. Be extremely careful of dust disposal, materials in fine particle form may be explosive. Before opening the dust canister lid, it is recommended to loosen dust from the microfilter dust canister by gently striking it against a solid surface (Fig. 9). Do not use the power tool if the switch does not turn it on and off. 5). You may grip the tool on top or around the motor housing as shown, which was contoured for that purpose (Fig. For this reason, it is possible to select a higher OPM for the random orbit sander than the recommended RPM for a standard polisher. Twist the canister left or right and simply pull away from the tool (Fig. measures reduce the risk of starting the tool accidentally. BM 2609140467 08-07 8/28/07 8:54 AM Page 6, Functional Description and Specifications, Disconnect the plug from the power source before making any ! Before opening the dust canister lid, it is recommended to loosen dust from the microfilter dust canister by gently striking it against a solid surface (Fig. Larger sandpaper will extend beyond the sanding pad causing snagging, tearing of the paper or kick-back.